$187.00/Each

This product is no longer available. We've left this page up for reference only.

Usually Ships in 2-3 Weeks from manufacturer

Lead times vary based on manufacturer stock

Product Overview

  • 4" centers
  • 1.5 GPM aerator
  • Cerama cartridge
  • 1/2" NPSM male inlets
  • Single lever handle
  • Chrome-plated brass body
  • Vandal resistant

Shipping Restrictions

This item cannot ship to CA
UPC Code:671262783231

T&S Brass and Bronze Works B-2710-WS-VR Specs

Quantity
1/Each
Shipping Weight
5.8 lb.
Spout Length
4 3/8 Inches
Faucet Width
5 3/4 Inches
Faucet Height
5 15/16 Inches
Faucet Centers
4 Inches
Features
With Drain
Flow Rate
1.5 GPM
Handle Type
Lever
Mounting Style
Deck Mounted
Spout Clearance
2 1/4 Inches
Spout Type
Cast
Type
Faucets
Water Inlet Size
1/2 Inches

T&S Brass and Bronze Works B-2710-WS-VR Details

This T&S B-2710-WS-VR deck mounted faucet is the perfect solution when you need a reliable water fixture for hand-washing in your facility. It boasts a set of 4" centers for easy installation while its integral spout and 1.5 GPM aerator flow device deliver gentle water flow that's perfect for hand-washing applications.

This faucet is engineered for maximum durability and uses a Cerama cartridge to adjust the temperature and flow rate. This cartridge contains ceramic discs that form a long-lasting water tight seal. When the lever handle of the faucet is pushed up, the discs spin to allow water to pass through. T&S cartridges are designed with efficiency and convenience in mind, allowing you to swap out one piece in the event of a leak, instead of replacing multiple moving parts.

Overall Dimensions:
Spout Length: 4 3/8"
Faucet Height: 5 15/16"
Faucet Width: 5 3/4"

Attention CA Residents:

Customer questions about this product

Can I use this product to serve drinking water?

This product is not intended for use in applications where potable (drinking) water is dispensed for human consumption.

Does this item have any additional agency approvals and certifications?

There are a wide range of regulations that govern plumbing code! We attempt to list any current certification marks with an official logo on the product page for your convenience. However, additional approvals, codes, and standards this product adheres to may be listed on the product specsheet.

I live in California. Can I purchase this product?

This product cannot be shipped to California.

What measurements do I need to install a faucet?

When installing a faucet, these are some of the most common measurements you’ll need:

Faucet Centers: If your faucet has a base with 2 inlets, measure the distance from the center of one inlet to the center of the other. This number must match the spacing of your building’s water lines (adjustable centers will help with the spacing). If mounting through the backsplash on a sink, the center measurement must also fit within the pre-drilled mounting holes.

Flex Hoses: If your faucet has flex hoses make sure that they will reach your building’s water lines.

Spout length: Make sure that the faucet spout will fit comfortably over your sink bowl and not extend too far / not far enough. If you plan to use a swing spout over a multi-bowl sink, make sure it will reach all of the bowls.
Ask your own question!
  • ADA Compliant

    ADA Compliant

    This item meets criteria established by the Americans with Disabilities Act (ADA).

  • CSA, Canada

    CSA, Canada

    This product has been certified by the Canadian Standards Association (CSA) to meet requirements for electrical, plumbing, and/or mechanical products in Canada.

  • NSF/ANSI/CAN 61 (Certified by CSA)

    NSF/ANSI/CAN 61 (Certified by CSA)

    This item is certified by CSA to meet the drinking water system component standards for Canada and the United States outlined in NSF/ANSI/CAN 61.

  • NSF/ANSI/CAN 372 (Certified by CSA)

    NSF/ANSI/CAN 372 (Certified by CSA)

    This item is certified by CSA to meet the drinking water system component lead content standards for Canada and the United States outlined in NSF/ANSI/CAN 372.

  • EPA WaterSense

    EPA WaterSense

    This item is certified by the EPA's WaterSense program to meet its standards for water use. WaterSense-labeled products are certified to use at least 20 percent less water, save energy, and perform as well as or better than regular models.

  • Made in America

    Made in America

    This item was made in the United States of America.

  • 1/2" Water Connection

    1/2" Water Connection

    This unit comes with a 1/2" water connection for water supply.

Resources and Downloads for
T&S Brass and Bronze Works B-2710-WS-VR

A PDF viewer is required to view this product's information. Download Adobe Acrobat software