SentrySafe SFW205BPC Black 1 Hour Fire and Water Safe with Biometric Fingerprint Lock and Keypad - 2 Cu. Ft.
- Biometric fingerprint lock gives secure and easy access with just a touch
- Bolts into the floor to ensure your valuables stay put
- Protects against 1700 degrees Fahrenheit for 1 hour
- Durable steel construction, 6 large 1" bolts
- 2 cu. ft. capacity with interior shelf, key rack, and tray organization
Other Products from this Line
First, find the yellow tag marked screw removal located on the inside of your safe door. Note that the shipping screw may be in one of several locations on the inside of the door. This video will demonstrate how to remove the screw from one location. Follow the instructions on the yellow tag to remove the shipping screw. If the tag has been removed, simply use a Phillips-head screwdriver, and rotate the screw counterclockwise until the screw falls out. Once the screw is removed, please be sure to test your combination with the door open to ensure the safe will lock and open properly. For additional how-to videos, please visit SentrySafe.com.
SentrySafe fire safes are shipped with a shipping screw inserted into the door to prevent them from locking during shipping. Check out the video for step-by-step shipping screw removal instructions, and ready your safe for immediate use.
Before we begin, please make sure to note these three functions of the fingerprint scanner: a green light will blink to indicate the safe is in program mode. Each user will have the availability to program two fingerprints. Turning the key pad sound off may make it more difficult to use the fingerprint scanner as a single beep indicates your finger has been scanned. Now locate the owner's manual and navigate to the heading—"Primary Fingerprint User." To register a primary fingerprint, first ensure the door is OPEN. Press the [P] button. Then, enter the 5-digit factory code. This safe is set to 44183. The blue light will flash to indicate the fingerprint sensor is ready to scan a new fingerprint. Then, swipe the first finger five to ten times on the scanner. Between each swipe, you should hear a single beep to indicate the fingerprint was scanned. When the safe has registered your first fingerprint, the green proceed-light will flash three times, and you will hear three beeps.
To register a second primary-user fingerprint, immediately repeat the finger swiping process with another finger, swiping it five to ten times on the scanner, noting again that you should hear a single beep between each swipe to indicate the fingerprint was scanned. Press the [C] button to complete fingerprint registration. Be sure to test your new fingerprint several times, with the door in the OPEN position, prior to closing and locking your safe.
To "Delete A Primary Fingerprint User," press the [P] button. Enter the 5-digit factory code found on the back of this owner's manual. Swipe either programmed fingerprint once. Then, press [C]. This will delete both fingerprints. Please note the electronic lock will NOT indicate that it has deleted the user's fingerprint—please test to make sure that it has been deleted. For additional how-to videos, please visit SentrySafe.com.
Follow these step-by-step video instructions to programming your SentrySafe Fire Safe's fingerprint scanner function. SentrySafe safes equipped with the fingerprint scanner function can be programmed to register primary-user fingerprints, in addition to the fingerprints of other users will be granted access to the safe.
Before we begin, locate the 5-digit factory code located on the back of your owner's manual, and enter the code to open the door. This safe is set to "62044." To program the primary-user code, press the [P] button and enter the 5-digit factory code on the electronic keypad. The green proceed-light will flash green, then you will have five seconds to enter your own personal 5-digit user code. In this case, we will use "12345." When the green proceed-light flashes, your primary user code has been saved.
To program the secondary user code, press the [P] button two times, then enter the 5-digit primary-user code on the electronic keypad. The green proceed-light will flash green. Then, you will have five seconds to enter your own 5-digit secondary user code. In this case, we will user "56789." When the green light flashes, your personal secondary user code has been saved. Please note the [C] button is a "clear" key. This can be used at any time to clear the system and start over. Be sure to test your new user codes several times, with the door in the OPEN position, prior to closing and locking your safe.
To delete the secondary user code, press the [P] button two times, and enter the 5-digit user code. Immediately after, enter "0-0-0-0-0" to delete the code. To delete the primary user code, press the [P] button once, and enter the 5-digit factory code on the keypad, and enter "0-0-0-0-0" to delete the code. For additional how-to videos, please visit SentrySafe.com.
Follow these step-by-step video instructions to use the electronic keypad to program, test, or delete your SentrySafe Fire Safe's primary and secondary user codes.
Independent tests show that not all competitive safes offer adequate fire protection. SentrySafe fire safes are designed, built, and tested to meet tough UL standards for one full hour of actual fire exposure (up to 1700 degrees Fahrenheit. Some competitive safes are fire-rated to only twenty minutes, with temperature ratings below the UL standards. Your SentrySafe products also provide powerful protection against water intrusion, and tough impact resistance that works even if a fire destroys the floor beneath the safe. SentrySafe—peace of mind for a lifetime.
Choose SentrySafe fire safes for unmatched protection of your important documents and keepsakes. UL-approved to withstand up to one full hour (approximately 1700 degrees Fahrenheit) of fire exposure, SentrySafe fire safes provide a level of fire-resistance that excels above other competitive safes. SentrySafe fire safes also provide an excellent defense against water intrusion.
|Sentry Safe SENSFW205BPC Specs|
|Width||18 5/8 Inches|
|Depth||19 5/16 Inches|
|Height||23 13/16 Inches|
|Interior Width||14 13/16 Inches|
|Interior Depth||11 15/16 Inches|
|Interior Height||19 5/8 Inches|
|Capacity||2 cu. ft.|
|Made in America||Yes|
|Protection Type||Fire and Water|
Sentry Safe SENSFW205BPC Details
Protect business documents, personal items, records, keys, and other valuables with this SentrySafe SFW205BPC black fire safe with biometric fingerprint lock and keypad. The 2 cu. ft. interior is great for your small and medium size possessions, and the compact size of the unit makes it a perfect fit for businesses and offices tight on space. With a biometric fingerprint scanner for easy access, you can rest assured knowing that your most prized belongings are safe from intrusion, yet easily accessible when you need them most. The safe's 1 hour fire protection means that its contents will not be charred or burned in the event of a fire. This safe can sit in 8" of water for up to 24 hours without water damage to your safe's contents. For neat organization in your safe, an adjustable shelf, key rack, door tray, and deep door pocket are included to hold items separate from the rest of the safe's contents.
With an all steel body and door construction, you won't have to worry about the unit being broken into. The door boasts a user-friendly battery-powered lock that provides much greater security than a standard key lock which can easily be lost, stolen, or copied. The unit can be programmed for 2 users with 2 finger prints each to allow for quick access. Plus, since the lock is battery-powered, you don't have to worry about power outages as they may be an issue with electric locks. The interior lighting allows you to easily see your valuables, no matter where you choose to place the safe. Six large, 1" thick bolts engage to hold the door closed, and a bolt-down kit is included with pre-drilled holes to ensure no one will be able to haul away the safe in its entirety.
Width: 18 5/8"
Depth: 19 5/16"
Height: 23 13/16"
Width: 14 13/16"
Depth: 11 15/16"
Height: 19 5/8"
Made in America
This item was made in the United States of America.
Sentry Safe SENSFW205BPC
Get paid to review this product!
If you've used this product, simply log in and share your text, video, and photo reviews of it. The customers on the left did it, and you can too! Earn up to $16.00 per product.Login or Register