Hobart FP250-1 Continuous Feed Food Processor - 3/4 hp
$4,826.36/EachShips free with Plus
Contact us for pricing
Call 717-392-7472 (Mon-Thur 24 Hours, Fri 12AM-8PM EST
Sat & Sun: 9AM-4PM EST)
Customers Also Viewed
plus $478.99 / Each
- Occupies minimal counter space
- 120/60/1 electrical connection
- 17 lb. per minute production capability
- 420 RPM plate speed
- Easy-to-operate ON-OFF switches
- Convenient angled front
- 3/4 hp
You May Also Need View All Items
Hobart 15SLICE-5/32CR-SS 5/32" Stainless Steel Slicing / Crimping Plate
Hobart 15PLATE-3PACK-SS 3 Plate Kit with Wall Rack
plus $769.00 / Each
Hobart 15PLTSS-6PACK Plate Kit
plus $1,819.00 / Each
Hobart 15SLICE-5/32-SS 5/32" Stainless Steel Slicing Plate
Hobart 15SLICE-7/32-SS 7/32" Stainless Steel Slicing Plate
Hobart 15SLICE-1/16-SS 1/16" Stainless Steel Slicing Plate
Hobart 15SLICE-1/8-SS 1/8" Stainless Steel Slicing Plate
Hobart 15SLICE-3/8-SS 3/8" Stainless Steel Slicing Plate
The Hobart FP250-1 continuous feed food processor is perfect for quickly slicing or shredding fresh vegetables.
You'll significantly reduce your needed prep time for various large orders with this powerful feed food processor. Each unit is designed with a 50-degree angled front for operator convenience and rapid product loading. A large, full-size feed hopper supports processing capabilities for a wide variety of products while permitting continuous cutting of long ingredients. With this unit's help, you'll never precut again!
This item meets the standards imposed by NSF International, which focuses on public safety, health, and the environment.
Made in America
This item was made in the United States of America.
This item has been tested and meets safety standards imposed by the Underwriters Laboratories (UL).
This unit comes with a NEMA 5-15P plug.
Powerful and Quick
With a 420 RPM plate speed, this unit quickly and easily cuts, chops, slices, and dices whatever you need to process to help your commercial kitchen reach optimum productivity. It boasts 17 lb. per minute production capabilities, which equates roughly to a weighty 1020 lb. per hour, thanks to its mighty 3/4 HP, 8 amp motor with included overload protection.
The food processor's handle is designed to facilitate comfortable repeated use.
Your machine will stay in place on any surface with its four non-slip rubber feet.
Compact and Intuitive
This food processor takes up little space and takes little effort to understand! It occupies minimal counter space with its small 9 13/16" wide footprint. With its simple on-off switches and an interlocking switch that keeps the machine from operating when the pusher plate isn't correctly in place, you can be sure that this food processor is an easy-to-use, efficient, and safe product for your commercial kitchen.
Hobart FP250 Continuous Feed Food Processor
Learn how to install, operate, clean, maintain, and even troubleshoot your Hobart FP250 continuous feed food processor with this informational video!
Immediately after unpacking the FP250, check for possible shipping damage. If the unit is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. To lift and move the food processor, grasp the handle at the back of the base with one hand and grasp the discharge shoot on the front with the other hand. Prior to installing the food processor, verify the electrical circuits to make sure that it agrees with the specifications on the machine data plate. The data plate is located on the back of the food processor. The food processor should be placed on a sturdy, level surface. There should be adequate space around the food processor for the user to operate the controls and to place and remove pans and bowls under the discharge shoot.
Warning: The electrical cord on this machine is equipped with a 3-prong grounding plug which must be connected to a properly grounded receptacle. If the receptacle is not the proper grounding type, contact an electrician. Do not remove the grounding prong from the plug.
To install the pusher plate, grasp the pusher plate handle with both hands and place the pusher plate shaft into the food processor's hole. Note: the pusher plate and handle must be at the 10 o'clock position (while looking down at the feed hopper) before it can be fully inserted into the hole. Push the pusher plate all the way to the bottom. Check the following before you install the cutting plate or ejector plate. First, press the "on" button. Then, lift the pusher plate with the pusher plate handle and move the plate to the left. Make sure the food processor stops running. Now, move the pusher plate to the right and lower the pusher plate. With the feed hopper in operating position, make sure the food processor starts. Make sure the food processor doesn't turn on when the pusher plate is lowered and the feed hopper is removed. If the food processor fails any of these tests, contact your local Hobart service office. To install the cutting plate, lift the pusher plate and move it to the left away from the feed hopper. Turn the locking knob counter-clockwise to unlock the feed hopper. Raise the feed hopper, center the ejector plate on the shaft and with the slots and ejector plate aligned with the pins and the coupling, push the ejector plate down to the bottom of the shaft and onto its coupling. Turn it counter-clockwise to lock. If you're dicing or chopping, insert a dicing grid and turn it until the holding pin fits into the notch. Avoid contact with the sharp knife on the cutting plate and put the desired cutting plate on the shaft and turn the cutting plate until it falls onto its coupling. Turn it counter-clockwise to tighten. Now, put the decoring screw on the shaft. Turn it counter-clockwise to tighten. The decoring screw uses left-hand threads. Move the feed hopper back into position. Finally, turn the locking knob counter-clockwise to lock the feed hopper in place. To remove the cutting plate, lift the pusher plate handle and move it to the left, away from feed hopper. Turn the locking knob counter-clockwise to unlock the feed hopper. Raise the feed hopper. Remove the decoring screw by turning it clockwise with a wrench. Remove the cutting plate, dicing grid (if used), and ejector plate from the food processor.
Warning: Rotating knives inside. Always use the pusher plate. Keep hands out.
Caution: Do not put meat, dough, or frozen foods in the food processor. Remove all hard parts that can damage the cutting blades, such as apple and pineapple stems, mango pits and fiberous cores.
Let's take a look at the controls of the FP250. The pusher plate presses food items against the cutting blades. It's controlled by a large pusher plate handle that wraps around the feed hopper. The food processor can be started by pressing the green "on" button and stopped by pressing the red "off" button. The "on" button needs to be pressed only if the "off" button is pressed or after connecting the electrical power cord. The food processor restarts automatically when the pusher plate is centered over the feed hopper and lowered. It stops automatically when the pusher plate is raised and moved to the left of the feed hopper or when the feed hopper itself is raised. The pusher plate must be turned to the left to load food into the feed hopper. Be sure to press the "off" button and unplug the FP250 food processor power cord before cleaning or changing the cutting plates. The full-size feed hopper processes large, round-like items such as loaves of bread, heads of lettuce, pineapple, honeydew, and cabbage. In addition, small, round items such as tomatoes, potatoes, and beets can be stacked against an inner-support wall inside the hopper. To operate the food processor with the feed hopper, raise the pusher plate and move it to the left. Put your produce into the feed hopper. Press the green "on" button. Now, move the pusher plate to the right and lower it into the feed hopper. The food processor will start when the pusher plate enters the feed hopper. Press down on the pusher plate handle with light pressure.
Note: best product quality is achieved when only light pressure is used to keep the product in contact with the cutting plate.
The feed tube processes long and thin items such as carrots, cucumbers, celery, and scallions. It can also be loaded with small, odd-shaped items such as mushrooms, shallots, and garlic cloves. The feed tube pusher sits in the feed tube when not in use, doubling as a cover. Removing the feed tube pusher doesn't stop the food processor from running. To operate the FP250 with the feed tube, begin by positioning the pusher plate over the feed hopper and lowering it to the bottom. Turn the feed tube pusher to unlatch it, remove the pusher. Put the food item into the feed tube and put the feed tube pusher on top of the food item. Press the "on" button and press down on the feed tube pusher with light pressure. Best product quality is achieved when only light pressure is used to keep the product in contact with the cutting plate. Speaking of cutting plates, here's a quick look at what each of them can do for you:
Standard Slicer: for slicing firm produce
Crimping Sliver: for ripple slicing
Fine Slicer: for slicing very thin slices
Dicing Grids: for dicing vegetables
For more detailed information about each of the plates, consult your operator's manual. A wall rack is available to hang the cutting tools for easy access to the operator and to protect the sharpness of the blades.
Warning: Turn the machine off and unplug the electrical cord before you begin any cleaning procedure.
Caution: Do not clean stainless steel with bleach containing cleansers like automatic dishwashing detergent. Bleach can corrode stainless steel. Do not clean the aluminum parts with high alkaline detergents like automatic dishwashing detergents or with hot water. Black aluminum oxide can form.
Nickel-plated parts including plates stamped with a "DW" and the feed hopper may be washed in an automatic dishwasher.
Caution: Do not spray the food processor with a spray bottle or hose and do not scrape with metal objects that can scratch the surface.
Immediately after use, removable parts must be cleaned with warm water and soap. Thoroughly rinse and dry with a soft, clean cloth. Remove the feed tube pusher, lift the pusher plate and move it to the left. Lift and remove. Turn the locking knob counter-clockwise to unlock the feed hopper. Raise the feed hopper and slide it off its hinged pins. Unthread the decoring screw clockwise with a wrench and remove it. Remove the cutting plate and, if used, the dicing grid. Use the brush to push remaining food through the dicing grid. Remove the ejector plate. Remove the food waste from the discharge shoot and cutting plate chamber. Use a clean cloth with warm, soapy water to wipe the cutting plate chamber, discharge shoot, and motor housing.
Note: use caution to prevent liquid from entering the pusher plate mounting hole.
Use a clean cloth with clean water to rinse the cutting plate chamber, discharge shoot, and motor housing. Again, use caution to prevent liquid from entering the pusher plate mounting hole. Wipe the cutting plate blades dry with a clean cloth and put the cutting plates on the wall racks. Put the ejector plate on the shaft until it drops onto its coupling and turn it counter-clockwise to lock. Put the decoring screw on the shaft and turn it counter-clockwise and tighten only for storage. Put the feed hopper on its hinge pins and lower it into the operating position. Return the pusher plate and feed tube pusher to their operating positions.
Each week, do the following checks. With the power cord connected to the outlet, test the safety interlock switches.
Warning: unplug the machine power cord before you do the following maintenance procedures.
With the power cord unplugged from the outlet, inspect the power cord and make sure it's in good shape. Look for cuts, fraying, or cracking. Make sure the pusher plate shaft moves freely. If it doesn't, clean and dry it and lubricate it with several drops of mineral oil. Make sure the cutting blades are sharp. If not, have them sharpened or the cutting plate replaced. All cutting plates can be replaced and all, except the dicing grids, can be sharpened. The dicing grids should be replaced every 8-18 months, depending on use.
If the food processor doesn't start, possible causes include the pusher plate may be raised, the feed hopper isn't in the operating position, or the branch circuit protector may be tripped. To remedy this, try moving the pusher plate over the feed hopper and lower. Put the feed hopper in operating position and check the fuse or circuit breaker panel for a blown fuse or a tripped circuit breaker. If the food processor stops while operating and doesn't restart, check to see if the pusher plate is raised and moved to the left. Check to see if a branch circuit protector is tripped or the motor is overheated. Move the pusher plate over the feed hopper and lower it. Check the fuse or circuit breaker panel for a blown fuse or a tripped circuit breaker and let the motor cool down until it automatically restarts. If food is cut poorly or slowly, you could be using the wrong cutting plates. Check the cutting plate guide in your manual. The cutting plates could be dull or nicked. Sharpen or replace the cutting blades. And you may be pressing the pusher plate handle too hard. Remember to press down on the product lightly. If the cutting plate can't be removed, it may be clogged with built-up food particles or the ejector plate isn't used. Using protective leather gloves, rotate the cutting plate clockwise to release. If you find that the decoring screw can't be removed, it too may be clogged with built-up food particles. Turn the decoring screw clockwise with the wrench. Finally, if you hear a scraping noise either the dicing grid isn't down in its coupling or the decoring screw isn't installed. Remove the diving grid and clean any debris on the walls and ledge of the cutting plate chamber and reinstall the grid. Also, install the decoring screw. This concludes operator training for the FP250 food processor. For more information, consult your manual, contact your local Hobart authorized service office for any repairs or adjustments needed.
- Width: 9 13/16 Inches
- Depth: 17 3/4 Inches
- Height: 23 1/16 Inches
Resources and Downloads for
A PDF viewer is required to view this product's information. Download Adobe Acrobat software
RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure or other damages resulting from installation in non-commercial or residential applications. The right is reserved to deny shipment for residential usage; if this occurs, you will be notified as soon as possible.
Other Products from this Line
Hobart FP150-1 Continuous Feed Food Processor - 1/2 hp
Hobart FP350-1B Continuous Feed Food Processor with 6 Plates - 1 hp
Hobart FP400i-1 Continuous Feed Food Processor - 2 hp
Hobart FP100-1 Continuous Feed Food Processor - 1/3 hp
Hobart FP350-1 Continuous Feed Food Processor - 1 hp
Leave a review of this product!
If you've used this product, log in and leave a review to tell us and other customers what you thought about it. Get paid up to $16 for submitting one of the first text, photo, or video reviews for this item. View your account for details.Login or Register