Hobart 6115 20 lb. Portable Potato Peeler
- Peels 15 - 20 lb. of potatoes in 1 - 3 minutes
- Made of seam-welded polished stainless steel
- Uses an abrasive, silicon-carbide disc for controlled peeling
- 1/3 hp motor
- Adjustable 4 minute timer
- Double V-belt drive
- 115V, 60Hz., single phase electrical with a 5 1/2' cord and plug
White Glove Delivery - Available -
You May Also Need
Your Hobart model 6115 potato peeler is constructed and designed to give long, satisfactory service, providing it is properly used and maintained. This training video will cover the operation, cleaning, and maintenance of the model 6115 potato peeler.
The 6115 potato peeler is designed to peel 15 to 20 pounds of product in one to three minutes using a 1/3 horsepower motor.
Where applicable, fit the rubber fill hose connector over any cold fresh water tap. Close and latch the discharge chute door. Note: The discharge chute door must always be left open when the unit is not in use. Position the hopper top in place on the peeler housing. Pour the product into the hopper. There should be room in the hopper for the product to move around while peeling, so do not overload the peeler. The capacity to remember is 15 to 20 pounds, maximum. Turn on the water supply. Turn on the peeler. Peeling times will vary depending on the type and condition of the product. When the desired degree of peeling has been reached, turn off the water. Place a container under the discharge chute to catch the product, and open the discharge chute door. After the product has been completely discharged, turn off the peeler, and it’s ready for a repeat operation. If the peeler is equipped with a peel trap or basket, it will be necessary to empty the peel trap drawer, or basket, occasionally.
WARNING: Unplug the machine power cord before beginning any maintenance or cleaning procedure. The peeler should be cleaned after the peeling operation has been completed. As soon as the peeling operation has been completed, and before the hopper has had time to dry, turn on the water, and flush the interior of the hopper. Then turn off the water. Remove the hopper top and clean it in the sink. Turn on the water again, and thoroughly clean the interior of the hopper, using a mild soap, and a brush, and rinse thoroughly. Clean the housing beneath the abrasive disk with mild soap and water and rinse thoroughly. NOTE: If the abrasive disk should stick and isn’t easily removed, it may be loosened by removing the hex head screw on top of the hub, and threading a longer screw, such as a 5/16 inch, 18 by 1 1/2 inch, in until the disc loosens. If the peeler is equipped with a peel trap, remove the peel trap drawer and thoroughly clean the drawer, as well as the peel trap interior. The discharge chute must be left open when the unit isn’t in operation, in order to prolong the life of the door seal.
WARNING: Unplug the machine power cord before beginning any maintenance or cleaning procedure. This machine is equipped with a manual reset overload protection switch. If during operation, the motor should overheat and trip this switch, turn the peeler switch off and allow the motor to cool for several minutes. To reset the switch, remove the bottom screw from the cover plate, rotate the cover plate, and push the red button. If the overload protection switch persists in tripping, contact your local Hobart service office.
This concludes operator training for the Hobart model 6115 potato peeler. To obtain service and parts information concerning the 6115, contact your local Hobart service office.
Learn how to properly operate, clean, and maintain the Hobart 6115 potato peeler in this informative video.
|Hobart 6115-1 Specs|
|Width||16 1/2 Inches|
|Height||24 1/2 Inches|
|Made in America||Yes|
Hobart 6115-1 Details
This Hobart 6115 potato peeler is constructed of seam- welded, polished stainless steel and peels 15-20 lb. of potatoes in 1-3 minutes. The peeling element on the 6115 is an abrasive, silicon- carbide disc that gives you controlled peeling at its finest, and can be removed when cleaning the inside. The 6115 features include 1/3 hp motor and a synchronous 4 minute timer that is adjustable for any increments from 1/2 minute to up to 4 minutes. The water inlet on the 6115 is rear-mounted and an air-gap model. The 6115 also has a double V-belt drive, stainless steel peel trap, and a Lexan liner. It requires a 115/60/1 electrical connection.
Width: 16 1/2"
Height: 24 1/2"
This Item Ships via Common Carrier. For more information and tips to help your delivery go smoothly, click here.
This item has been tested and meets safety standards imposed by the Underwriters Laboratories (UL).
Made in America
This item was made in the United States of America.
Resources and Downloads for
A PDF viewer is required to view this product's information. Download Adobe Acrobat software
RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure or other damages resulting from installation in non-commercial or residential applications. The right is reserved to deny shipment for residential usage; if this occurs, you will be notified as soon as possible.
People Talk About:potato's Equipment peeler Potato home Hobert Hobart help hand great
We own the Hobart Potato Peeler, it is a great equipment for our Kitchen, it help us reducing our time on a 1/4 that it used to be, and we don't see a lot of waste, it is an amazing Equipment!!
The Hobert 20lb. Portable Potato peeler. Is a must when you serve home made mashed potato's.It peel's 15-20 lb.of potato's in 4 min. by hand it takes forever.Easy to cean.
Get paid to review this product!
If you've used this product, simply log in and share your text, video, and photo reviews of it. The customers on the left did it, and you can too! Earn up to $16.00 per product.Login or Register