Hi I'm Jamie I'm going to show you how to put a PJ unit on our single trailer. We're going to start by removing these clips in the front here. They are held in place by these D clips, simply pull the spring off the back side of the clip and then pull the pin out of the hole. Remove that clip and we'll do the same thing for the other side. And we will slide the unit up onto the trailer we're gonna have the door facing forward which is the recommended placement of the unit on the trailer. You can place the unit with the door facing the rear however caution must be taken to lock that door anytime the unit is transported otherwise the door can be flinging open. You can lift it up onto the trailer here, and then we will push it all the way forward until it is held in place by the C clips on the back. You'll see the unit is secured underneath this C clip, the C channel here that's welded onto the trailer that holds it in place in the back and then we are going to now install these on the front. We're going to reinstall these simply the same way we uninstalled them except opposite. Simply place that into the hole, line up your pin, through the clip, and then fasten it in place with the clip there. We'll do the same thing with the other side. Now you'll see that there is a little bit of play when you put the unit onto the trailer, that is only to allow for other manufacturer trailers or units to be put on the trailer. These clips are held in place by welded in pins here and they are going through the assembly of the trailer so it makes it very secure and it is held onto the base of the unit which is the strongest part of the unit. We are going to start by putting our tongue into the trailer here. There is a receiver located in the center front of the trailer to do this we'll pull the pin out of the this keeper pin here and pull all the wiring out and then we will slide our tongue into position and you can put this pin partially in the hole, push this through until it goes through, and then secure in place with your cotter pin. Now we are going to start with the left wheel assembly here. We are going to pull the pin out of the axle, and pull this D clip out of the front receiver clip here. Taking our wheel assembly, place that onto the axle, slide it into position, put your clip back in. Now we are gonna do the same thing with the right assembly, removing the clip, see the D clip there, place our wheel assembly back on. Replace our pin in the back and we will now lower the unit down; to do this it can be a little tricky we'll have to pull this wheel assembly out to clear the clip and then up into the clip. We'll do the same thing for the other side. And we are ready to hook it up to our trailer. Now when you get to your job site and have released your trailer from your truck, lower it to the ground and we will begin by lowering the wheel assemblies down to lower the whole unit. It is done by pulling these clips out like this, pushing this down, and out. And lowering this unit to the ground. And then we will do the same thing for the other side. Now at this point you can leave the wheel assemblies attached. Now if your unit is facing the front like this one is you will need to remove the tongue. To do that we're going to pull this pin out here, your clevis pin. Put that to the side. Remove your tongue. Pull this out, push our wires underneath the unit and I would recommend that you would place this in the back of your truck or wherever for safe keeping that will keep your unit secure while on the job site and keep anyone from taking your unit. Thank you for watching this safety instructional video on how to use the PJM3 on this trailer. These trailers are available for all units that we carry, the Fleet or PJM3 units. The PJ part number is a TUO11000 and the Fleet is a tTUO11001. This is also available as a double trailer where you can put 2 units on a trailer that would be a TUO2100 for a PJ model and a TUO1001 for a Fleet. Now if you'd like any more information on this unit please visit out website and I thank you for watching.
Copy and paste the embed code above.
Ensure safety while setting up your PolyJohn unit by making sure you can transport the unit to and from your location with ease. This video will show you how to safely and securely attach a unit to a trailer so you can move it around without a problem.
Slice and dice with speed and precision! With the Saber King, you can prepare all of your fresh produce with just one unit, from shredding lettuce for subs to slicing tomatoes for chili. Find out more by watching this short, informational video.
Add durability and safety to your commercial kitchen with the Mercer Genesis 8" forged chef’s knife! It’s NSF Listed and comes with a long-lasting santoprene handle that stands up to kitchen oils and high heat for a non-slip grip.
User Data Policy
The Leading Distributor of Restaurant Supplies and Equipment
Based in Lancaster, PA, WebstaurantStore is the largest online restaurant supply store serving food service professionals and individual customers worldwide. With thousands of available products and over 5.5 million orders shipped, we have everything your business needs to function at its best. Over the years we have expanded our selection of wholesale supplies and commercial equipment to include healthcare, educational, and hotel supplies.
Our focus is your convenience – order online from your laptop, desktop, or smartphone 24 hours a day, 7 days a week. Our fast shipping, low prices, and outstanding customer service make WebstaurantStore the best choice to meet all of your professional and food service supply needs.