$11,563.86/Each

Contact us for details

Call 717-392-7472 (Mon-Thur 24 Hours, Fri 12AM-8PM EST
Sat & Sun: 9AM-4PM EST)

Protect Your Product with Safeware

Protection Powered by Safeware

  • Easy to clean
  • Open-frame stainless steel construction
  • 3 hp motor for durability and reliability
  • Adjustable legs
  • Direct gear-drive transmission
  • Small footprint
  • 142" blade
Shipping:
Hobart 6801 Meat Saw

Hobart 6801 Meat Saw

The following operator training video on the Hobart 6801 meat saw is a supplement to the instruction manual that came with your Hobart meat saw. If you have any questions concerning operation, please consult your manual.

Your Hobart 6801 meat saw is constructed and designed to give long, satisfactory service, providing it is properly used and maintained. This training video will cover the controls, operation, cleaning, and maintenance of the 6801 meat saw.

Controls
Electrical control of the 6801 meat saw consists of this switch knob. Pull to turn the saw on and push to turn the saw off.

Operation
Safety devices incorporated in this saw must be in their correct operating positions anytime the saw is in use. Before turning the saw on, raise or lower the upper guide and guard assembly by grasping the hand knob and sliding it up or down so the cutting zone is only as high as necessary for the piece being cut. All doors, covers, and guards must be in their operating position closed while the machine is running. Always keep hands well back from the blade and maintain control of the product. Using the pusher plate makes it unnecessary to hold your hand near the cutting edge of the saw blade. The pusher plate is used to hold meat against the gauge plate when slicing short ends. A slot in the pusher plate and a stop on the right flanged end of the carriage is provided for proper positioning of the pusher plate. Hold the pusher plate handle with your right hand and always maintain a safe distance from the blade. When not in use, keep the pusher plate under the carriage support.

Now, we will demonstrate an operation using both the traveling and stationary carriage. When using the traveling carriage, stand in front of the machine. Lean lightly against the front of the carriage as you move the carriage to the left, passing the product through the blade at a steady and uniform rate. Use your left hand to remove and stack cuts, always reaching behind the blade. Never reach in front of the blade. Return the carriage to the right, pulling the product toward you and away from the blade.

When using the stationary carriage, lock the carriage in position by pulling the spring-loaded carriage lock out, rotating it 90 degrees, and sliding the carriage until the lock engages. To unlock the carriage, pull the carriage lock out, and rotate it 90 degrees so it rests on its bracket. When sawing with the stationary table, observe the same safety procedure of reaching behind the blade when removing or stacking product. Never reach in front of the blade.

Cleaning
Warning: Disconnect electrical power and place a tag at the disconnect switch indicating the circuit is being worked on before cleaning this machine. The saw must be thoroughly cleaned and sanitized before first use, after each day's operation, anytime it is not to be used for an extended period of time, and before being put into operation after an extended down time. Each saw can be cleaned with high pressure cleaning equipment available from other suppliers, or it can be disassembled and its components cleaned in a sink. In either case, a pH cleaning agent mixed per the supplier's instructions should be used. After washing, thoroughly sanitize, rinse, and dry the saw and all components.

Disassemble the following components to allow access to all areas for cleaning: the upper pulley cover, lower cover scrap pan, the table's right and left hand, the scrap tray, carriage, column guard, pulley wiper, blade scrapers, lower blade guide assembly, saw blade (refer to maintenance section of this video), upper guide and guard assembly, and the upper and lower pulleys. Use a cloth or brush to clean the base unit. For reassembly, a light coating of tasteless mineral oil should be applied to all metal surfaces. Lubricate 6 ball bearings on the carriage with a small amount of mineral oil. Apply a few drops of mineral oil to the gauge plate slide rod and work the gauge plate assembly back and forth a few times. Reassemble the saw components in reverse order of disassembly, making sure all parts are properly assembled. If using high pressure cleaning equipment, scrape the machine and its components to remove any scrap particles before cleaning. Thoroughly hose the saw and its components following the equipment supplier's instructions. Be sure to get the hose stream into all corners. Stubborn soil may require a little brushing.

Maintenance
Warning: Disconnect electrical power supply and place a tag at the disconnect switch indicating the circuit is being worked on. The motor has permanently lubricated ball bearings and requires no lubrication. The slide bar for the upper guide and guard assembly also require no lubrication. Occasionally, you should apply a small amount of mineral oil to the six ball bearing rollers underneath the carriage. On a more frequent basis, the gauge plate slide rod and the pulley shafts need a few drops of tasteless mineral oil. If changing saw blades, disassemble the components as described in the cleaning section of this tape. Reinstall the blades so the teeth point to the right and down.

This concludes operator training for the Hobart 6801 meat saw. To obtain service and parts information concerning the 6801 meat saw, contact your local Hobart service office.

Copy and paste the embed code above.

Watch this informative video to learn how to operate, clean, and maintain your Hobart 6801 meat saw.

Hobart 6801-18 Specs
Width 38 1/4 Inches
Depth 34 Inches
Height 73 1/2 Inches
Cutting Clearance Width 17 1/4 Inches
Cutting Clearance Height 15 3/4 Inches
Hertz 60 Hertz
Phase 3 Phase
Voltage 200 - 230 Volts
Blade Size 142 Inches
Horsepower 3 HP
Installation Type Floor Model
Power Type Electric
Type Band Saws

Hobart 6801-18 Details

For precise cuts, simple operation and outstanding durability, look no further than this Hobart 6801-18 142" vertical meat saw! The 5/8" x 142" blade with 3 teeth per inch is powered by a direct gear drive transmission that provides a 4150 FPM blade speed to easily cut through bone, without having to worry about dust thanks to a large lower scrap pan. This heavy duty meat saw features a rugged gauge plate that ensures you have precise regulation of cut thickness, while a center crown pulley design combines with retaining double flanges to provide you with consistent performance over the long haul without the loss of blade integrity.

A 16" x 24 1/4" movable carriage tray offers labor-saving convenience thanks to a stepped front edge and tri-rail support that makes movement fast, simple, and stable. It features an 21 1/2" x 39 5/8" stationary cutting table that provides a large stacking space and simple breakdown for cleaning, which is also a snap! Simply remove the parts (no tools needed!) and wash, while giving the open frame design a high-pressure hose-down. This unit has a 200/230/60/3V electrical rating.

Overall Dimensions:
Left to Right: 38 1/4"
Front to Back: 34"
Height: 73 1/2"

Cutting Clearance:
Width: 17 1/2"
Height: 15 3/4"

This Item Ships via Common Carrier. For more information and tips to help your delivery go smoothly, click here.

Because this item is not stocked in our warehouse, processing, transit times and stock availability will vary. If you need your items by a certain date, please contact us prior to placing your order. Expedited shipping availability may vary. We cannot guarantee that this item can be cancelled off of the order or returned once it is placed.

  • NSF Listed

    NSF Listed

    This item meets the standards imposed by NSF International, which focuses on public safety, health, and the environment.

  • Made in America

    Made in America

    This item was made in the United States of America.

  • UL US & Canada

    UL US & Canada

    This item has been tested and meets safety standards imposed by the Underwriters Laboratories (UL) for use in the United States of America and Canada.

  • Hardwired

    Hardwired

    This product must be hardwired; it does not plug into a standard wall outlet.

Resources and Downloads for
Hobart 6801-18

Spec Sheet Specsheet Manual Manual Hobart's Warranty Information Warranty Parts Diagram Diagram

A PDF viewer is required to view this product's information. Download Adobe Acrobat software

Warranty Info

RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure or other damages resulting from installation in non-commercial or residential applications. The right is reserved to deny shipment for residential usage; if this occurs, you will be notified as soon as possible.

Leave a review of this product!

If you've used this product, log in and leave a review to tell us and other customers what you thought about it. Get paid up to $16 for submitting one of the first text, photo, or video reviews for this item. View your account for details.

Login or Register

Find Related Products