Ships free with Plus
  • Single hole base with 2 1/4" flange; 1/2" BSPP male inlet flex hoses
  • 44" flex hose; 1.42 GPM 5SV Equip spray valve
  • Lever handles with color coded screws
  • Equip ceramic cartridges; can withstand water temperatures up to 180 degrees Fahrenheit
  • Includes 6" wall bracket and 8" add-on faucet; 38 9/16" overall height
  • Chrome plated brass construction
  • EPAct 2005 Compliant

UPC Code:


Usually Ships in 1 Business Day
When will I receive my item?

You May Also Need

"You May Also Need" items are guaranteed to work with the item you are viewing, such as lids that will fit a cup or casters that will fit a piece of equipment. If an item is not listed in this section, we do not guarantee that it will work with the product you are viewing and do not recommend that you purchase them for use together.

T&S: Installing and Converting a Pre-Rinse Unit

T&S: Installing and Converting a Pre-Rinse Unit

Installing a pre-rinse unit. Depending on the type of T&S pre-rinse unit purchased, installation follows 1 of 2 simple procedures. A typical installation for our traditional models or a pop and lock installation for our easy install models. But no matter the method, T&S makes it easy to be up and running in no time. Now lets get started. All supplies are packaged neatly in the box to help avoid lost parts. Begin by shutting off the water supply and draining the lines. Apply Teflon tape or pipe joint compound to the water supply lines. Install the coupling flange to the water line nipple and tighten to the wall or deck. Insert the coupling nut washer and attach the faucet to the flange. Tighten the coupling nut with a wrench and then turn on the water to test for leaks. Apply Teflon tape to both ends of the riser included in your assembly. Install one end of the riser into the top of your faucet and tighten it by hand. Slide the hook halfway down the riser you just installed and tighten the screw temporarily. Hand tighten the spring assembly to the top end of the riser and then tighten it with an adjustable wrench. In the process you will also be tightening the riser you installed. It is important that the spring assembly be installed properly, with the closed coil end at the riser. Now adjust the height and position of the hook, so the spray valve hangs loosely when secured by the hook. You don't want to put unnecessary strain on the spring assembly. Turn the water supply back on and check for any leaks, making adjustments if any are needed. When installing the long riser you should also install a wall bracket assembly for added support. Also you can easily install an add-on faucet between the riser and the base faucet body. Now that the unit is properly installed, you can begin using your new T&S Brass pre-rinse unit. Just make sure your employees turn off the water at the faucet when they are done using this product. At T&S, we understand the last thing our customers need are long, tedious installations. That's why we developed easy-install pop and lock pre-rinse units for even easier installation. The pop and lock feature cuts installation time by 66%. Here's how it works. Simply slide the easy-install nut onto one end of the riser. Apply Teflon tape to the top of the threads on the riser and attach to the spring assembly. Tighten the spring body and the riser assembly with a wrench in a counter-clockwise direction. Make sure the easy-install locking washer is seated properly inside the faucet body. Grab the riser assembly and lower the easy-install end fitting into the faucet body. Press down until the end fitting pops in place. Then, lock the easy-install locking nut in place and tighten with a wrench in a clock-wise direction. What if you have a pre-rinse unit that you'd like to convert to a standard faucet? There are only a few steps necessary to perform this change. Begin by turning the water off at the source. Loosen the swivel nut and remove the riser assembly and the easy-install locking washer. Next, grease the end of the swing nozzle or gooseneck swivel. Insert the end into the faucet base, twist, and push into place. Now, tighten the swivel nut by hand and snug it up with a wrench. Turn the water on, check for leaks, and the faucet is once again ready for use. As you can see, our pre-rinse unit exemplifies our distinctive T&S quality, as well as easy installation and removal. With our unique pop and lock system. At T&S we make the installation of our products simple through innovative engineering and cutting-edge design, with reliability built in.

Copy and paste the embed code above.

This video goes over the simple process of installing or converting a T&S pre-rinse unit. With 2 easy procedures, these faucets are sure to ease your experience.

Equip by T&S 5PR-2S08 Specs
Hose Length 44 Inches
Add-On Faucet 8 Inches
Cartridge Type Ceramic
Faucet Centers Flex Inlets
Handle Type Lever
Installation Features Support Bracket
Maximum Water Temperature 180 Degrees F
Pre Rinse Unit Type Hose and Spring
Spray Valve Flow Rate 1.42 GPM

Customer questions about this product

I have a chemical injection system on my compartment sink. Can I use my pre-rinse faucet to supply water to it?
Yes! Item B-TEE-RGD is a rigid tee assembly that installs easily into an existing T&S pre-rinse faucet (or you can use it on a brand new faucet) and provides you with a means to deliver water to a chemical injection system, or other, similar sink accessories that may require a water supply.
How is the pre-rinse hose length measured?
Unless otherwise specified, the quoted hose length includes any grips or connectors at the end of the hose, so the actual working length of the hose may be slightly less than described. Please refer to the product's specsheet for more detailed dimensions.
Ask your own question!

Equip by T&S 5PR-2S08 Details

This Equip by T&S 5PR-2S08 deck mounted pre-rinse faucet features a 44" flex hose and spring design that provides plenty of versatility in a variety of warewashing applications! A 1.42 GPM spray valve makes it easy to clear food debris off of dishes before washing them, and an ergonomic squeeze handle allows easy and intuitive use. Additionally, an 8" add-on swing faucet makes your sink even more versatile, allowing you to switch between the pre-rinse setup and normal faucet depending on what you need! To make installation easy, it also boasts in-line check valves and 1/2" BSPP male inlets on 18" flexible connector hoses.

- 44" flex hose with spring is great for many pre-rinse applications

- 1.42 GPM spray valve (5SV) with ergonomic squeeze handle

- Lever handles with color coded screws for durability and easy operation

- Ceramic cartridges provide excellent durability and leak-resistance since there is no seat washer

- 8" add-on swing faucet is perfect for times when you need water but don't need a pre-rinse faucet

- Includes wall bracket for added support, and in-line check valves

- 38 9/16" overall height

- Durable chrome plated brass construction

WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

Resources and Downloads for
Equip by T&S 5PR-2S08

Get paid to review this product!

If you've used this product, simply log in and share your text, video, and photo reviews of it. The customers on the left did it, and you can too! Earn up to $16.00 per product.

Login or Register