This Product is no longer availableBrowse our full selection SEE MORE PRODUCTS
Workshop WS12045F2 3-4.5 Gallon Fine Dust Wet / Dry Vacuum Filter - 2/Pack
This product is no longer available. We've left this page up for reference only.
- 3-layer material traps fine dust, ashes, chalk, or cooled fireplace ashes
- Captures particles down to 1 micron with 99% efficiency rate
- Large surface area resists clogging and improves airflow
- Quik-Lock fastening system for easy and convenient installation
- Durable, washable material
- 3-4.5 gallon capacity
- For dry use applications only
Watch this video to see a simulation of vacuumed dust being filtered by a Workshop standard filter cartridge.
Step 2: Access and remove filter. Access by unlatching and removing lid from dust drum. Then, remove the filter. This process varies and is covered more thoroughly in your owner's manual.
Step 3: Gently tap the filter against the inside wall of your dust drum and the debris will loosen and fall.
NOTE: It is recommended to clean in an open, ventilated area. Because cleaning will put dust in the air. If you have allergies or health concerns it may be prudent to replace the filter.
Remove debris. Be sure to examine for damage such as rips and tears. If damaged, replace before use. Another method to remove debris is to use compressed air. Set a low pressure to prevent damaging filter.
Step 4: Clean with water. To clean a wet filter, or other appropriate filter, run water through the filter from a hose or spigot. Take care that water pressure from the hose is not strong enough to damage filter.
Step 5: Dry filter. Allow filter to completely dry out before storing or using.
For better vacuum performance, keep your filters clean and free from rips or tears to help protect vacuum performance and life. For additional, more detailed information, refer to the WORKSHOP Whitepaper on the subject and your owner's manual.
It is extremely important to keep your vacuum filter clean to help ensure the longevity of your vacuum. Watch this video to learn the proper way of cleaning your vacuum filter, so you can have the best results with your vacuum!
Step 2: Remove the filter. Using the patented Qwik Lock Fastening System makes installing and removing your filter quick, easy, and secure. First, hold the filter tabs of the Qwik Lock filter in each hand. With one thumb on the Qwik Lock stud, which protrudes through the integrated filter plate, lift up on the filter tabs while pushing down on the stud. This action will cause the filter to release from the filter cage. Slide filter off cage.
Step 3: While this will be more thoroughly covered in another video, if filter is in overall good shape, clean filter in one of the following ways: in a well ventilated area, tap filter on the side of a trash can to dislodge debris, blow off the filter using compressed air, or wash with water.
Step 4: Replace the filter. Replacing a filter is similar to removing it in reverse. Slide the Qwik Lock Filter over the filter cage. Align the small center hole in the top of the filter over the Qwik Lock stud on the filter cage. Press down on the outside edge of the filter to seat rubber gasket. Press firmly on top of the filter near the stud to snap over the ball on the end of the stud.
Step 5: Continue use. If filter is properly attached, return and latch the motor cover onto the dust drum. Continue use in accordance with your owner's manual.
For additional, more detailed information, refer to the WORKSHOP Whitepaper on the subject and your owner's manual.
Interested in the proper way of changing or replacing a wet / dry vac filter? Check out this how-to video for the step-by-step process!
Don't get stuck in a situation where a room has flooded, and you have no easy way of cleaning up the mess! With a wet/dry vac from Workshop, not only can you suck up small spills, but you can quickly eliminate several inches of standing water from anywhere!
Workshop WS12045F2 Details
Capture fine particles like sawdust, chalk, flour, and cement / drywall dust with this Workshop WS12045F2 3-4.5 gallon fine dust wet / dry vacuum filter! Thanks to the washable, pleated paper material, this filter offers a large surface area that improves airflow and resists clogging during routine use. When you're done, simply wash the filter and use it again.
For exceptional cleaning performance, this filter catches microscopic particles down to 1 micron with a 99% efficiency rate, ensuring that you're getting a deep, thorough clean with every use. And, for added convenience, the Quik-Lock filtration fastening system makes removing and installing your filter quick, easy and secure.
Resources and Downloads for
A PDF viewer is required to view this product's information. Download Adobe Acrobat software
Leave a review of this product!
If you've used this product, log in and leave a review to tell us and other customers what you thought about it. Get paid up to $16 for submitting one of the first text, photo, or video reviews for this item. View your account for details.Login or Register