Nemco N55200AN-6 Easy Slicer Fixed Vegetable Cutter, 3/16"
- Slice fruit or vegetables in seconds
- Great for sandwiches and pizza toppings
- NSF Listed
Petrol-Gel Food Grade Sanitary Lubricant - 4 oz. Tube
Nemco 45457 Replacement Foot
Nemco 55163 Clamp Assembly for Easy Slicer
Nemco 55157-1 Adjustable Slicing Assembly for Easy Slicers
Nemco 55257 Sharpening Stone for Easy Slicers
Nemco 55261-4N 1/8" Fixed Cut Slicing Assembly for Easy Slicers
Nemco 55261-6N 3/16" Fixed Cut Slicing Assembly for Easy Slicers
Nemco 55261-8N 1/4" Fixed Cut Slicing Assembly for Easy Slicers
Nemco 55263-1 3/16" Easy Slicer Shredder Assembly
Nemco 55263-2 5/16" Shredder Assembly for Easy Slicers
Nemco 55816 Portable Base for Easy Slicer
Nemco 55261-5N 5/32" Fixed Cut Slicing Assembly for Easy Slicers
The Easy Slicer from Nemco is the one slicer you need to make fast, easy work of most fruits and vegetables. In seconds you can produce mounds of uniformly sliced fresh vegetables for salad bars, sandwiches, pizza toppings, and more, all with minimal training and big savings in time and labor. Its adjustable stainless steel blade provides a full range of slicing options from 1/16" to 1/2" in thickness for maximum versatility and convenience.
This instructional video is not intended to take the place of the supplied written instructions. Please take the time to read through the instructions thoroughly and become familiar with the operating and maintenance procedures.
We will be using the standard mounting base that comes with each unit. It is attached to the work table with the screws provided in the mounting kit. Also available is the Nemco easy mounting board, a handy optional accessory. The NSF-approved mounting board is held firmly to any smooth surface with heavy duty suction cup feet. It is easily removed for cleaning or storage with a simple effort-free tug on each cup's pull tab.
Now, we will begin the demonstration by sliding the Easy Slicer into the mounting base and tightening the locking screw to secure the machine. Check the slice thickness setting. Remove the adjustable slicing unit by turning the shaft lock to the left and pulling on the handle. The slice thickness is easily adjusted by holding the handle stationary and by turning the adjusting screw at the end of the adjusting shaft assembly. The thickness of the slice is indicated by the alignment of the pin in the slot and the lines on the recessed portion of the main shaft. These lines are 1/16" apart, so two lines equals 2/16", or 1/8". Three lines equals 3/16", et cetera, up to 1/2". Simply turn the thumb screw to lock in your setting on the easy-to-read calibrated gauge.
Now pull out the pusher handle, raise the cover plate, and place your produce into the trough. Close the cover plate, and gently push on the pusher handle knob while turning the handle on the rotary cutting unit in a clockwise direction. You may want to turn your handle about a quarter turn counter-clockwise before turning in the cutting direction. This will permit a running start as the blade makes its first cut. Maintain uniform pressure on the pusher handle. Heavy pressure is unnecessary and will not improve the slicing or shredding action. As you can see, it is very fast and easy to achieve very uniform slices with clean-cut edges.
The Easy Slicer was designed for easy disassembly for cleaning as follows. Turn the shaft lock assembly to the left and pull the rotary slicing unit out of the trough and leg assembly. Lift the guard off the trough and leg assembly. Loosen the locking screw and remove the trough and leg assembly from the mounting base. After cleaning, return the trough and leg assembly to the mounting base and tighten the locking screw. Slide the guard onto the trough and leg assembly, and then slide the rotary slicing unit into the leg assembly. Turn the shaft lock assembly clockwise, to the right, to lock the rotary slicing assembly into the trough and leg assembly. You will want to periodically clean the shaft lock bore with the brass brush provided with the Easy Slicer to assure that the shaft lock assembly turns freely.
To remove the shaft lock for cleaning, rotate the shaft lock assembly to the left to release the rotary slicing assembly. Slide the rotary slicing assembly out of the trough and leg assembly. Remove the guard. Pull the shaft lock pin to release the shaft lock. Pull the shaft lock out of the trough and leg assembly. Use the supplied brush to clean the shaft lock channel. (For a written version of these instructions, please refer to the cleaning instructions available online or in the literature provided with each new machine.) Replace the shaft lock into the trough and leg assembly. Return the shaft lock pin through the trough and leg assembly and shaft lock. Be certain that the shaft lock is fully seated into the channel, and then rotate it to the right, or clockwise.
To prolong the sharpness of your blades, they can be honed as follows. Remove the rotary slicing unit from the trough and leg assembly. Adjust to the maximum slice width, 1/2". Use a fine honing stone on the beveled side of the blade. Move the stone parallel to the blade's grain, and work along the curve of the blade. Be sure to maintain the original sharpening angles on the beveled side of the blade. If needed, use the hone on the flat side of the blade to remove burns. A honing stone is available from Nemco for this purpose.
In order to replace the slicer blades, remove the rotary slicing unit from the machine, as for cleaning, and secure it in a vise. Using a screwdriver, remove the flathead screws, releasing the blades. We highly recommend using cut resistant gloves during this procedure - these blades are extremely sharp.
Some of you may only require a single size cut, and an adjustable unit may not be required. Nemco offers fixed cut machines available in widths of 1/8", 3/16", and 1/4". There are also two shredder blades available in widths of 3/16" and 5/16".
Control your portions, save time, reduce your labor costs, and maximize your menu capabilities with the versatility of the Easy Slicer from Nemco. For more information about this or our other fine Nemco products, contact us at Nemco Food Equipment, or visit us online at www.nemcofoodequip.com.
This Nemco Easy Slicer is ideal for slicing fruits and vegetables. It easily mounts to countertops or other flat surfaces, and can be removed in seconds for cleaning or storage.
|Depth||10 3/4 Inches|
|Slice Thickness||3/16 Inches|
Customer questions about this product
- Can this unit be modified to cut in different sizes?
- Yes! Below are the accessories you will need to convert this unit to the given size.
1/16"-1/2" Adjustable Cut: 55157-1 Blade Assembly
1/8" Fixed Cut: 55261-4N Blade Assembly
1/4" Fixed Cut: 55261-8N Blade Assembly
3/16" Shredder: 55263-1 Blade Assembly
5/16" Shredder: 55263-2 Blade Assembly
5/32” Fixed Cut: 55261-5N Blade Assembly
7/32” Fixed Cut: 55261-7N Blade Assembly
7/64” Fixed Cut: 55261-MN Blade Assembly
The Nemco N55200AN-6 Easy Slicer
features a 9 1/4", fixed,
stainless steel blade with
3/16" openings and a mounting
base for a secure
vegetable cutting workstation. The Nemco N55200AN-6
is great for producing evenly cut
fresh vegetables and fruits
in seconds, for fruit and
salad bars, sandwich and
pizza toppings, and more. The Nemco
N55200AN-6 Easy Slicer mounts to
countertops and other flat
surfaces, and can be removed
in seconds for storage or
cleaning. NSF Listed.
Depth: 10 3/4"
This item is also known as 55200AN6.
Commercial Sandwich / Salad Preparation Refrigerators
Clear Hinged Take Out Containers
Wall Mounted Write On Menu Boards, Non-Illuminated
Day of the Week Dots & Product Labels
Frequently Purchased Together
Have you used this product?
Log in to write your own review and earn up to $16.00 with video, photo, and text reviews!Login or Register