Your new impinger is equipped with three diagnostic messages to help you troubleshoot a specific problem yourself or at least help you narrow it down. The messages you might encounter on the digital display are: 1. LP, left probe fail or RP, right probe fail. This occurs when there is no temperature being sent to the controller from the baking chamber. This generally means a malfunctioning or failed thermoprobe. 2. shorted probe. This occurs when a constant temperature signal is being sent from the controller to the baking chamber. This will happen if there's no heat being supplied to the oven for some reason. This can occur if the gas valve is shut off or disconnected. 3. belt jam. This will occur when there is a conveyor motor failure. These messages should be noted and communicated when calling your Lincoln authorized service agent. Now, let's talk about what to do if your impinger oven seems to be malfunctioning, but there are no diagnostic messages displayed. Before you make a service call, there are a few things you should check out. We'll look at troubleshooting in terms of the symptom you observe and what might be causing it. You go to turn on the oven at the beginning of the work day and it did not respond by heating up. Always suspect the easy stuff first. Is the oven plugged in tightly? Check the temperature indicator light. Does it show that the oven is heating? If not, see if the temperature is set to the right temperature. If the thermostat is set right, see if the main fan is working by checking for air movement. If there is no air movement, the fan isn't working, so check the main circuit breaker and the main fan fuses on the oven. If you find a bad fuse, replace it. If the fuses are okay and you have an electric oven, there is nothing more you can do. Your authorized Lincoln service agent must be contacted. If the fuses are okay and your oven is gas-fired, be sure the main shut-off valve is open. Check for kinks in the gas hose and make sure the gas connector is firmly locked into its receptacle. Beyond this, there is nothing more you can do. Your authorized Lincoln service agency must be contacted. Burnt products result from too high a temperature, too long a cooking time, or improperly installed calumniating panels. First, see if all the fingers are installed properly. Then check the temperature set point. If the temperature is set properly, but the products are overcooked, the oven could be out of calibration. If the timer shows it's set properly, time it against a stopwatch. Start the stopwatch when the leading edge of the pan enters the oven. Stop the watch when the leading edge exits the oven. If the conveyor speed mechanism needs re-calibration, your authorized Lincoln service agency must be contacted. In the meantime, you can try to compensate by adjusting the conveyor speed up or down until help arrives. Under-cooked products can result from several tings. First, be sure you are not placing the food product too far into the oven cavity. The leading edge should be just at the conveyor opening. And don't pull the product out of the oven too soon. Next, if the temperature is set properly, but the products are under-cooked, the oven could be out of calibration. If the conveyor speed shows it's set properly, time it against the stopwatch using the "leading-edge-in, leading-edge-out" method we used earlier. Again, if the time/temperature mechanism needs calibration, your authorized Lincoln service representative should be contacted. And, of course, you can compensate by adjusting the belt speed up or down until help arrives. If time and temperature aren't your problem, it could be the calumniating panels were not installed properly. If you're still having a problem, see if the main fan is working by checking for air movement. If the fan isn't running, check the main circuit breaker and the main fan fuses. If you have a gas-fired oven, check to be sure the main shutoff valve is open. Check for kinks in the gas hose, and be sure that the gas connector is firmly locked to its receptacle. If you do all this and the oven is still not performing properly, it's time to call your authorized service agency. Another situation you might run into is a conveyor belt that won't move. If this happens, your display might show the diagnostic message "belt jam." This occurs when the conveyor motor fails, so you'll need to call your Lincoln authorized service agency. If this does not happen, check to see that the belt speed control is not accidentally turned all the way down. Check the drive sprocket chain to they're connected properly. Take corrective action as needed. Next, check your main circuit breakers and fuses. If the conveyor stopped when the oven was hot, it could be overheating. Check and clean the ventilation louvers and cooling fan covers, if needed. It could also be a mechanical malfunction. With the circuit breaker off, so the conveyor cannot start accidentally. disconnect the drive sprocket chain. Then, gently push and pull the conveyor to see that it moves freely. If it doesn't, look for some obstruction or binding. If the conveyor moves freely, then turn the circuit breaker back on. Turn the oven on and check to see if the motor shaft is rotating. If the motor drive shaft won't turn, you'll have to call your authorized Lincoln service agency.
Copy and paste the embed code above.
Troubleshooting with the 1600 series Impinger ovens from Lincoln. This video offers an overview of diagnostic messages as well as what you can do to ascertain exactly what your oven needs done!
Based in Lancaster, PA, we are the leading restaurant supply store providing restaurant supplies and equipment to the foodservice industry and individual customers worldwide. With more than 5.5 million orders shipped, our large stocked inventory and fast shipping make us the best choice to fill your needs.
We securely accept:
You haven't entered an email address!
We will be unable to respond to your comments without your email address. If you wish to submit your comment without an email address, please click "Give Feedback"