Hobart FP150-1 Continuous Feed Food Processor - 1/2 hp
- Free Shipping!
Contact us for pricing
Call 717-392-7472 (Mon-Thur 24 Hours, Fri 12AM-8PM EST
Sat & Sun: 9AM-4PM EST)
- Occupies minimal counter space
- 120/60/1 electrical connection
- 14 lb. per minute production capability
- 396 RPM plate speed
- Easy-to-operate ON-OFF switches
- Convenient angled front
- 1/2 hp
"You May Also Need" items are guaranteed to work with the item you are viewing, such as lids that will fit a cup or casters that will fit a piece of equipment. If an item is not listed in this section, we do not guarantee that it will work with the product you are viewing and do not recommend that you purchase them for use together.
Hobart 15SLICE-5/32CR-SS 5/32" Stainless Steel Slicing / Crimping Plate
Hobart 15PLATE-3PACK-SS 3 Plate Kit with Wall Rack
Hobart 15PLTSS-6PACK Plate Kit
Hobart 15SLICE-5/32-SS 5/32" Stainless Steel Slicing Plate
Hobart 15SLICE-7/32-SS 7/32" Stainless Steel Slicing Plate
Hobart 15SLICE-1/16-SS 1/16" Stainless Steel Slicing Plate
Hobart 15SLICE-1/8-SS 1/8" Stainless Steel Slicing Plate
Hobart 15SLICE-3/8-SS 3/8" Stainless Steel Slicing Plate
Warning: Rotating knives inside. Always use the pusher plate. Keep your hands out.
Your Hobart food processor is used for slicing, shredding, grating, julienne cutting, and dicing vegetables, fruits, or cheese. The compact unit is designed for ease of operation and quick cleaning. Proper assembly including selection of the appropriate cutters is necessary for correct operation of the food processor. Refer to the cutting tool guide for cutters and refer to the appropriate operation instructions in your manual. To start the processor, push the green "start" button. To stop the unit, press the red "stop" button.
Warning: Rotating knives inside. Always use the pusher plate. Keep your hands out.
Interlock switches prevent the machine from operating when the feed hopper is out of position or the pusher plate is raised above the feed hopper during operation. The machine stops and this allows the pusher plate to be rotated counter-clockwise for loading. To continue operation, rotate the pusher plate clockwise until it's directly above the feed hopper. As the pusher plate begins to lower into the hopper, the machine will restart. You don't need to push the green "start" switch unless "stop" was pressed. Always push the red "stop" switch before changing cutters or cleaning. First, grasp the pistol grip handle, raise the pusher plate, and turn it to the left. Now, release the feed hopper lock by turning the finger panel counter-clockwise. Then, raise the feed hopper. Remove the locking screw by turning it clockwise. Always use the wrench when removing the locking screw. Lower the ejector plate on the knife shaft until the ejector plate seats on the shaft pin. Next, select the appropriate plate for the job. Place the plate on the shaft, turning until engaged. Lock the cutting tool by turning the locking screw counter-clockwise. Finally, lower the feed head. When the pusher plate is rotated and lowered, the feed head will automatically be locked. For operation that requires two plates: first, raise the pusher plate and turn it to the left. Now, release the feed hopper lock by turning the finger panel counter-clockwise. Then, raise the feed hopper. Remove the locking screw by turning it clockwise. Always use the wrench when removing the locking screw. Lower the ejector plate on the knife shaft until the ejector plates seats on the shaft pin. Select the proper sized dicing plate and place it correctly on the knife shaft, above the ejector plate. Select the appropriate slicing plate for the job by consulting the cutting tool guide in your instruction manual. Place the slicing plate on the shaft, turning until engaged. Lock the cutting tool by turning the locking screw counter-clockwise. The locking screw must always be used. Finally, lower the feed head. When the pusher plate is rotated and lowered, the feed head will automatically be locked. After the pusher plate is raised, prepared products such as potatoes, carrots, onions, lettuce, cabbage, etc. can be placed in the large feed hopper. The feed hopper has one fixed and one detachable partition wall. With the highest capacity and best cutting results, the detachable partition wall should be removed only when necessary because of product size. To remove the detachable partition, unscrew the two black knobs on the outside of the feed hopper. The fixed partition wall is used as support for round products such as lemons and tomatoes when producing slices for cross-cut or when you want the best possible results cutting potato chips, one stack only. For best results, it's advisable to remove the tops and tails from products such as lemons, limes, or onions and place them in the hopper perpendicular to the desired cut. When cutting French fries with a julienne cutter, position the potatoes at the lower right corner of the large feed hopper. The potatoes may be stacked to cut several at one time. For consistent results, stack product in the lower right corner of the feed hopper, one pile only. Twist the knob to release the catch on the feed tube pusher and pull out to expose the feed tube opening. The feed tube is used for slicing long, thin-shaped products such as cucumbers or carrots or to contain small items like radishes. The machine doesn't stop when the feed tube pusher is removed. This allows product to be processed continuously. Always use the feed tube pusher.
Warning: Turn the machine off and unplug the electrical cord before cleaning.
Clean the machine immediately after each use. Dismantle all removable parts from the machine and wash them in warm water and detergent. Rinse thoroughly and wipe dry with a soft, clean cloth. Wipe the exterior of the machine with a damp cloth. Allowing the food juices to dry on the machine may cause discoloration. Never clean the cutting tools or other aluminum parts in highly alkaline dishwashing solutions or in excessively hot water. This can cause formation of aluminum oxide which will appear black. DO NOT USE steel wool or sharp objects for cleaning machine surfaces if they become discolored; scratched surfaces become hard to keep clean. Remove the feed tube pusher and rinse in lukewarm water. Raise the pusher plate and turn it to the left. Remove the feed hopper and rinse it in lukewarm water. Remove the locking screw; always use the wrench. Lift out the cutting plate. If you have used the dicing grid, push the remaining leftovers through the grid with a nylon brush before removing. Remove the dicing plate and ejector plate, rinse in lukewarm water. Turn the pusher plate back counter-clockwise over the feed hopper and lower. Place a pan under the exit shoot and pour lukewarm water from the top through the knife chamber. Run a wet cloth through the feed tube, wipe with a clean, dry cloth. Return the cutting tools to the wall rack. Lower the ejector plate onto the knife shaft until the ejector plate seats on the shaft pin. Replace the locking screw.
Warning: turn machine off and unplug the electrical cord before doing any maintenance.
Routinely inspect the machine to ensure that it's in proper working order. Plates must be cleaned, intact, and sharp. Regularly lubricate the pusher plate shaft with a drop of mineral oil, not cooking oil. If the machine develops any problems, contact your local Hobart service office. Depending on usage, dicing grids become dull from wear with an average life expectancy from 8-18 months. Dicing grids can't be resharpened and are therefore expendable. Replacement dicing grids are available from your local Hobart service office. This concludes operator training for the Hobart FP150 food processor. To obtain service and parts information concerning the FP150, contact your local Hobart service office.
Watch this video to learn how to operate, clean, and maintain your Hobart FP150 continuous feed food processor!
|Width||8 1/4 Inches|
|Depth||18 5/8 Inches|
|Height||20 1/4 Inches|
|Capacity||14 lb. per minute|
|Made in America||Yes|
|Number of Discs / Blades Included||None|
|Type||Continuous Feed Processors|
The Hobart FP150-1 continuous feed food processor is perfect for quickly slicing or shredding fresh vegetables. Each unit is designed with a 50 degree angled front for operator convenience and rapid product loading. A large, full size feed hopper supports processing capabilities for a wide variety of products, while permitting continuous cutting of long products. Never precut again!
With its simple on-off switches and an interlocking switch that keeps the machine from operating when pusher plate isn't correctly in place, you can be sure that this food processor is an easy-to-use, efficient, and safe product for your commercial kitchen. With a 396 RPM plate speed, this unit quickly and easily cuts, chops, slices, and dices whatever you need to process to help your commercial kitchen reach optimum productivity.
Are you short on counter space, but still in need of a food processing workhorse? This unit takes up minimal counter space with its small 8 1/4" wide footprint but still manages to process up to 14 lb. of product per minute-that's 840 lb. per hour!
The Hobart FP150-1 continuous feed food processor features a powerful 1/2 hp, 4.8 amp motor with overload protection. Plates are sold separately.
Width: 8 1/4"
Depth: 18 5/8"
Height: 20 1/4"
This item has been tested and meets safety standards imposed by the Underwriters Laboratories (UL).
Made in America
This item was made in the United States of America.
This item meets the standards imposed by NSF International, which focuses on public safety, health, and the environment.
This unit comes with a NEMA 5-15P plug.
A PDF viewer is required to view this product's information. Download Adobe Acrobat software
RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure or other damages resulting from installation in non-commercial or residential applications. The right is reserved to deny shipment for residential usage; if this occurs, you will be notified as soon as possible.
Other Products from this Line
Hobart FP100-1 Continuous Feed Food Processor - 1/3 hp
Hobart FP100-1B Continuous Feed Food Processor with 6 Plates - 1/3 hp
Hobart FP150-1B Continuous Feed Food Processor with 6 Plates - 1/2 hp
Hobart FP250-1 Continuous Feed Food Processor - 3/4 hp
Hobart FP250-1B Continuous Feed Food Processor with 6 Plates - 3/4 hp
Hobart FP350-1 Continuous Feed Food Processor - 1 hp
Hobart FP350-1B Continuous Feed Food Processor with 6 Plates - 1 hp
Hobart FP400-1 Continuous Feed Food Processor - 2 hp
Choice Large Disposable Food Service Poly Gloves - 1000/Box
Day of the Week Stickers & Product Labels
Wet Area Floor Mats
Commercial Food Processors
Get paid to review this product!
If you've used this product, simply log in and share your text, video, and photo reviews of it. The customers on the left did it, and you can too! Earn up to $16.00 per product.Login or Register