WEBVTT

1
00:00:00.960 --> 00:00:05.640
<v 0>Okay, let's get started. Surface mount video number one. Hopefully you're ready.</v>

2
00:00:05.640 --> 00:00:08.370
You got your checklist, you've got your supplies and tools in place.

3
00:00:08.580 --> 00:00:11.430
Let's get started here in the restroom, I've got Brett and Chris,

4
00:00:11.520 --> 00:00:15.690
both from RMSE, Chris, our technician Brett. My goodness gracious.

5
00:00:15.780 --> 00:00:19.020
We're not making Chris's job any easier on him in this kind of environment.

6
00:00:19.080 --> 00:00:22.110
<v 1>Correct? No. We've given him a very small space to work in.</v>

7
00:00:22.350 --> 00:00:25.170
We've given him tile walls. The sinks are on top of him.

8
00:00:25.470 --> 00:00:27.180
This is about as difficult as it gets.

9
00:00:27.180 --> 00:00:29.790
<v 0>But if you can do it here, you can do it anywhere. Anywhere, absolutely.</v>

10
00:00:29.790 --> 00:00:32.490
Let's give hint. Let's give our viewers at home a bird's eye view.

11
00:00:32.490 --> 00:00:36.720
Let's get out of the shot and we're going to let Chris do his thing. Alright.

12
00:00:36.720 --> 00:00:40.440
Chris is removing the old paper towel dispenser in preparation for the hand

13
00:00:40.440 --> 00:00:40.770
dryer.

14
00:00:40.770 --> 00:00:42.210
<v 1>Install. Yes,</v>

15
00:00:42.210 --> 00:00:45.870
he's removing the old mounting hardware so that the dryer has a nice smooth

16
00:00:45.870 --> 00:00:50.400
surface to mount to Here Chris is marking the specific locations for the

17
00:00:50.400 --> 00:00:51.270
mounting holes.

18
00:00:52.020 --> 00:00:56.400
He's making sure to use the correct heights as specified by the manufacturer.

19
00:00:56.970 --> 00:00:58.860
The heights are located in the instructions.

20
00:00:59.820 --> 00:01:02.670
It's extremely important that the dryer meet certain A,

21
00:01:02.820 --> 00:01:04.590
a guidelines where applicable.

22
00:01:05.640 --> 00:01:10.320
Make sure you also use the correct tools such as a hammer drill as Chris is

23
00:01:10.320 --> 00:01:11.153
using here.

24
00:01:11.880 --> 00:01:15.630
It's also extremely important that the dryer be level upon installation.

25
00:01:16.410 --> 00:01:20.940
It's highly recommended that a trained professional perform this electrical

26
00:01:20.940 --> 00:01:23.910
installation. Here,

27
00:01:23.910 --> 00:01:28.110
the proper gauge wire is being routed into the electrical panel based on the

28
00:01:28.110 --> 00:01:29.850
voltage that the dryer is rated for.

29
00:01:30.600 --> 00:01:34.890
XLERATOR® comes in a range of voltages to meet varying electrical services.

30
00:01:37.860 --> 00:01:40.770
The wire is being routed to a new 20 amp breaker.

31
00:01:41.310 --> 00:01:44.730
XLERATOR® can also be installed on 15 amp breakers,

32
00:01:44.730 --> 00:01:49.020
which is important when retrofitting older buildings. Depending on the voltage,

33
00:01:49.020 --> 00:01:53.160
the dryer may need to be on a dedicated circuit and appropriate breaker.

34
00:01:53.640 --> 00:01:56.220
In this case, the dryer needs a dedicated circuit.

35
00:01:56.790 --> 00:01:59.850
One more wire and the XLERATOR® will be good to go.

36
00:01:59.910 --> 00:02:01.110
At the other end of the restroom,

37
00:02:01.800 --> 00:02:04.260
while the wired circuit is still off in the panel,

38
00:02:04.470 --> 00:02:07.800
Chris is bringing the other end down the wall with a snake in the location of

39
00:02:07.800 --> 00:02:10.050
the knockout on the XLERATOR® base plate.

40
00:02:10.740 --> 00:02:14.370
He is screwing the electrical connector to the base plate and following the

41
00:02:14.370 --> 00:02:18.450
electrical schematic sticker located on the hand dryer for wire connections

42
00:02:19.740 --> 00:02:20.820
with the power still off.

43
00:02:20.820 --> 00:02:24.780
The cover is installed to the hand dryer using two tamper-proof screws and a

44
00:02:24.780 --> 00:02:28.830
wrench, which are provided with all units. Lastly,

45
00:02:28.830 --> 00:02:31.350
power is installed and the unit is ready for use.

46
00:02:34.050 --> 00:02:36.990
XLERATOR® offers the XLERATOR®, hand dryer wall guard.

47
00:02:37.410 --> 00:02:41.670
The wall guard is an antimicrobial shield made specifically to fit underneath

48
00:02:41.670 --> 00:02:42.630
your hand dryer.

49
00:02:42.870 --> 00:02:46.680
This will protect your walls from water spray that may be blown off of wet hands

50
00:02:46.680 --> 00:02:50.580
by XLERATOR®'s. Powerful Airstream. To install the wall guard,

51
00:02:50.670 --> 00:02:53.370
clean the wall surface with isopropyl alcohol.

52
00:02:54.000 --> 00:02:57.630
This will make sure the surface is dry and free of any dust or debris.

53
00:02:59.890 --> 00:03:02.260
Center the wall guard underneath the hand dryer,

54
00:03:02.260 --> 00:03:05.770
so the top of the wall guard is one inch below the bottom of the dryer.

55
00:03:06.460 --> 00:03:09.490
Four strips of double-sided tape are included For each panel.

56
00:03:09.880 --> 00:03:14.080
Apply the tape strips to the textured side of the black or white panel in the

57
00:03:14.080 --> 00:03:16.900
smooth side of the brush stainless panel as shown.

58
00:03:18.100 --> 00:03:21.550
Lay the tape out according to the illustration that's included in your

59
00:03:21.550 --> 00:03:22.383
instructions.

60
00:03:24.160 --> 00:03:28.600
Press each tape strip firmly onto the plastic or stainless steel as it is

61
00:03:28.600 --> 00:03:32.350
applied. Continue until all four strips are applied.

62
00:03:33.670 --> 00:03:38.020
Alignment is critical. Once the wall guard is placed, it can't be repositioned.

63
00:03:41.230 --> 00:03:45.370
Align the top edge of the wall guard with the markings on the wall and firmly

64
00:03:45.370 --> 00:03:48.550
press into place if you'd like to.

65
00:03:48.970 --> 00:03:52.660
You could even apply a small bead of silicone sealant around the edge

66
00:03:53.830 --> 00:03:57.370
to clean your wall guard. Use mild soapy water and a soft cloth.

67
00:03:58.060 --> 00:04:01.360
Mild dish soap mixed with water in a spray bottle. Works best.

68
00:04:02.500 --> 00:04:07.390
Any cleaner that contains ammonia or abrasive cleansers should not be used on

69
00:04:07.390 --> 00:04:09.290
this surface. The.