WEBVTT

1
00:00:00.630 --> 00:00:02.070
<v 0>Welcome to video number two.</v>

2
00:00:02.130 --> 00:00:05.580
Now we have the proper surface mount and base established.

3
00:00:05.940 --> 00:00:10.680
Now it's time to talk about putting in the proper a DA compliant recess

4
00:00:10.680 --> 00:00:13.110
kit. Brett, we got to cut a hole in this fresh.

5
00:00:13.110 --> 00:00:17.580
<v 1>Green wall. Yes, exactly. This is the XLERATOR® recess kit.</v>

6
00:00:17.970 --> 00:00:21.720
It is going to allow you to put in an A compliant application.

7
00:00:22.080 --> 00:00:25.740
It's going to recess your dryer about three and a half to four inches,

8
00:00:25.740 --> 00:00:26.970
so if you're in a tight space,

9
00:00:27.270 --> 00:00:29.550
this will actually create more space for your walkway,

10
00:00:29.580 --> 00:00:31.200
give you a little better flow to your bathroom.

11
00:00:31.410 --> 00:00:32.310
<v 0>You can't put it in yourself,</v>

12
00:00:32.310 --> 00:00:35.850
but we highly recommend you need a skilled technician to do this kind of.

13
00:00:35.850 --> 00:00:35.940
<v 1>Work.</v>

14
00:00:35.940 --> 00:00:39.630
This is even going to take a more skilled technician than our last application

15
00:00:39.630 --> 00:00:42.420
because we are going to be cutting through drywall or for that matter,

16
00:00:42.420 --> 00:00:43.260
solid surface.

17
00:00:43.410 --> 00:00:46.530
<v 0>Okay, let's get started. Let's bring in our professional technician, Chris,</v>

18
00:00:46.530 --> 00:00:47.430
once again. Perfect.

19
00:00:48.060 --> 00:00:51.090
<v 1>Here Chris is measuring the cutout location for the recess kit.</v>

20
00:00:51.150 --> 00:00:55.260
He's marking straight lines at the proper recommended mounting height and having

21
00:00:55.260 --> 00:00:57.120
the cut fall in between wall studs.

22
00:00:58.920 --> 00:01:02.670
Using a reciprocating saw, it carefully cuts out a section of a sheet rock.

23
00:01:03.930 --> 00:01:07.170
It may be necessary to use different tools depending on the wall material,

24
00:01:07.770 --> 00:01:12.240
never hurts to undercut the rectangular section and then open it up slowly while

25
00:01:12.240 --> 00:01:15.060
test fitting the recess kit to ensure a nice fit.

26
00:01:16.050 --> 00:01:19.380
A non-live circuit, which has already been wired into the panel,

27
00:01:19.590 --> 00:01:23.550
is being routed to the recess kit and secured with an electrical connector.

28
00:01:24.930 --> 00:01:26.190
With that wire in place,

29
00:01:26.310 --> 00:01:29.250
Chris is sliding the recess kit into the cutout in the wall,

30
00:01:29.640 --> 00:01:34.050
fits nicely in place where it's not too tight that it cracks the sheet rock and

31
00:01:34.050 --> 00:01:35.940
not too loose where it falls out of the wall.

32
00:01:36.870 --> 00:01:40.350
The cutout was placed near a stud so that it could be screwed to the recess kit

33
00:01:40.590 --> 00:01:41.790
for proper support.

34
00:01:44.280 --> 00:01:47.790
Now that the recess kit is in place, the hand dryer is being mounted.

35
00:01:48.210 --> 00:01:52.290
This is being done by placing a dryer base plate over the six quarter inch,

36
00:01:52.290 --> 00:01:55.410
20 threaded studs using a nut driver.

37
00:01:55.470 --> 00:01:58.590
The dryer is mounted to the studs with the provided nuts.

38
00:02:03.060 --> 00:02:03.480
Again,

39
00:02:03.480 --> 00:02:08.160
it's important to have the correct tools as Chris has a nut driver here to mount

40
00:02:08.160 --> 00:02:08.993
the base plate.

41
00:02:10.050 --> 00:02:14.250
Chris is now finishing the wiring to the dryer again by following the wiring

42
00:02:14.250 --> 00:02:18.450
schematic located on the dryer. Here Chris is measuring the wires,

43
00:02:18.840 --> 00:02:22.110
cutting them to the correct length, making sure he doesn't have too much wire.

44
00:02:22.110 --> 00:02:23.250
Once he puts the cover on

45
00:02:25.950 --> 00:02:30.330
the recess kit has a unique hinging door which allows the dryer to tilt forward

46
00:02:30.330 --> 00:02:32.250
for easy mounting access of the cover.

47
00:02:32.820 --> 00:02:36.780
Two tamper-proof screws are removed to hinge the unit forward and the cover is

48
00:02:36.780 --> 00:02:39.630
mounted to the dryer by using two tamper-proof screws.

49
00:02:40.470 --> 00:02:43.470
The hinge door is being secured in place with two tamper-proof screws,

50
00:02:43.470 --> 00:02:45.240
which were removed to originally lower.

51
00:02:45.240 --> 00:02:50.130
The door power is turned on and the XLERATOR® installed in the recess

52
00:02:50.130 --> 00:02:51.840
kit is ready for use.