WEBVTT

1
00:00:01.680 --> 00:00:02.220
<v 0>Hello,</v>

2
00:00:02.220 --> 00:00:05.790
and in this segment we're going to show how to convert your Continental 

3
00:00:05.790 --> 00:00:09.180
undercounter or sandwich case from a door to a drawer.

4
00:00:12.330 --> 00:00:15.300
It's always recommended to disconnect the power to your cabinet

5
00:00:15.300 --> 00:00:19.920
before doing any service or modifications. In this segment,

6
00:00:20.010 --> 00:00:21.690
you're going to need the following tools:

7
00:00:23.370 --> 00:00:27.990
a Phillips screwdriver or a Phillips adapter for a drill,

8
00:00:28.560 --> 00:00:31.440
a cordless drill with an 1/8-inch drill bit,

9
00:00:33.180 --> 00:00:36.840
and six Phillips #8 truss head sheet metal screws,

10
00:00:37.140 --> 00:00:40.170
as well as a pair of pliers, not shown in the video, 

11
00:00:40.500 --> 00:00:42.930
to remove the vertical pilaster strips.

12
00:00:45.930 --> 00:00:47.730
Once the power has been disconnected,

13
00:00:48.120 --> 00:00:51.180
open the door and remove the top and bottom hinge screws.

14
00:00:51.480 --> 00:00:52.980
Set the door to the side.

15
00:00:53.280 --> 00:00:57.450
Also, remove the shelf and the sidewall vertical pilaster strips.

16
00:00:59.490 --> 00:01:01.830
Take the four hinge screws that you removed,

17
00:01:02.100 --> 00:01:05.040
reinsert into the four hinge holes, top and bottom.

18
00:01:10.590 --> 00:01:15.510
Your drawer cage assembly will consist of two drawers and the cage with the

19
00:01:15.510 --> 00:01:17.400
center volume that holds the drawers.

20
00:01:20.490 --> 00:01:21.660
Open the top drawer.

21
00:01:22.920 --> 00:01:27.120
Slide the locking clip for the slide forward and down 

22
00:01:27.120 --> 00:01:28.740
at the back.

23
00:01:29.640 --> 00:01:33.180
And remove the top and bottom drawers and set to the side.

24
00:01:36.120 --> 00:01:40.320
Carefully lift up and slide the cage assembly into the door opening.

25
00:01:41.130 --> 00:01:45.120
Ensure that the center mullian is flush with the front of the case.

26
00:01:46.380 --> 00:01:51.210
Locate the six mounting holes in the cage assembly and take your 

27
00:01:51.210 --> 00:01:56.040
1/8-inch drill and drill into the plastic breaker covers.

28
00:02:00.510 --> 00:02:04.470
Insert the six Phillips screws into the pre-drilled mounting holes.

29
00:02:05.340 --> 00:02:10.200
We installed the top and bottom drawer, locking the slide clip on right and

30
00:02:10.200 --> 00:02:14.520
left sides. Open and close the top and bottom drawers,

31
00:02:15.000 --> 00:02:18.930
making sure that they close properly, and that you have a good gasket seal.

32
00:02:20.340 --> 00:02:23.760
I hope this information was helpful, and if you need additional information,

33
00:02:23.760 --> 00:02:27.900
please contact the factory, or you can download the operation manuals from our

34
00:02:27.900 --> 00:02:31.920
website, www.continentalrefrigerator.com.