Contact us for pricing

Why do we do this?

Call 717-392-7472 (Mon-Thur 24 Hours, Fri 12AM-8PM EST
Sat & Sun: 9AM-4PM EST)

Due to a manufacturer's price increase, this price will increase by 1% to 4.5% on 02/01/18

  • Grinds 55 to 60 lb. of beef per minute
  • 7.5 hp grind motor; 1 hp mix motor
  • Grinds 60 to 65 lb. of pork per minute
  • Stainless steel finish
  • Pneumatic (air drive) foot control
  • 150 lb. meat capacity



Usually Ships in 2-4 Weeks

White Glove Delivery - Available -

What is White Glove service?

Standard common carrier delivery options cover the cost of getting an item to your shipping address but our White Glove delivery service does that and more!

The White Glove agent will call to schedule a Call Before Delivery within a four hour window, which gives you the flexibility to work around your busy schedule and to prepare the space where your item will be placed. Upon delivery, trained professionals will unload your large item from the truck, bring it into the room of choice, unpack the item and remove all packaging debris from the premises.

Please note that White Glove delivery will typically add 5 - 7 business days to your order's transit, and only includes 30 minutes of on-site time. If on-site time beyond 30 minutes is required, you may be responsible for additional fees. While the agents will bring the items into the location of your choice, this service does not include set-up of the items being delivered, such as installation of casters, shelves, or other accessories. Small items will not be unpackaged individually; they will be set in place and debris and packaging material will not be removed.

You May Also Need

"You May Also Need" items are guaranteed to work with the item you are viewing, such as lids that will fit a cup or casters that will fit a piece of equipment. If an item is not listed in this section, we do not guarantee that it will work with the product you are viewing and do not recommend that you purchase them for use together.

Hobart 1532 & 2032 Mixer/Grinder

Hobart 1532 & 2032 Mixer/Grinder

The following Operator Training video on the Hobart MG1532 and MG2032 Mixer/Grinders is a supplement to the instruction manual that came with your Hobart Mixer/Grinder. If you have any questions concerning operation, please consult your manual. Your Hobart Mixer/Grinder is constructed and designed to give long satisfactory service providing it is properly used and maintained. This training video will cover the controls, operation, cleaning, and maintenance of the MG1532 and the MG2032 Mixer/Grinders. The Mixer/Grinder has a heater in the control box and another heater in the front control panel to keep the controls dry. They are automatically on when the machine is electrically connected. The Mixer/Grinder should always be connected except when performing assembly, disassembly, cleaning, and maintenance of the machine. Electrical control of the mixer/grinder consists of the mix start button, which rotates the mixing arm, the stop button that turns the mixer/grinder off as well as the foot switch if it had been on, the mix/grind start button which starts rotating both mix arm and worm. Pressing the stop button stops mixing and grinding. The foot switch, when on, the mix start and mix/grind buttons are inoperable and the accessory foot switch can be used to mix/grind only. The indicator light shows when the foot switch is on. Push the stop button to turn the foot switch off. And finally, here is the hopper lid interlock. This switch requires the hopper lid to be closed before the machine can operate. Raising the hopper lid opens the electrical circuit and makes the machine inoperative. Before operating, the mixer/grinder and its parts should be clean and the knife and plate need some preliminary lubrication. Also, before operating, make sure the wedge cylinder, which is marked Top and Bottom, is in the proper position. The top marking should be visible. The grinder attachment can easily be removed for cleaning. Use the spanner wrench to loosen the adjusting ring and then remove the adjusting ring, plate, and knife. Next, loosen, but do not remove, the grinder attachment's two flanged nuts using the spanner wrench. Rotate the cylinder clockwise and remove the cylinder. Then remove the worm. At re-assembly, install the worm and then the cylinder. Make sure "top" is visible on the cylinder and the cylinder's flanged nuts are tight before assembling the knife, plate, and the adjusting ring. Use only the flanged nuts provided. Two studs on the front of the machine allow storage of the spanner wrench and the pneumatic foot switch. The rubber seal at the drive end of the worm can be removed by hand for cleaning. Grasp the outer flange of the seal or use a dull screw driver to pry the seal loose. Reinstall the seal before installing the worm. Before using the grinder attachment, take it apart and thoroughly wash it. The knife and the plate need some preliminary lubrication. Rub tallow or food grade mineral oil over the cutting faces of these parts. When assembling the knife be sure to turn the cutting edge towards the perforated plate. The notch on the circumferences of the plate must fit over the pin in the cylinder. Knives and plates must be sharp and true for proper cutting action. Keep the grinder attachment in a clean and sanitary condition. To remove the mixing arm, loosen the bushing retainer's two flanged nuts and remove the bushing retainer. Raise the hopper lid and pull the mixing arm from the square drive in, lifting the mixing arm from the hopper. On re-assembly, make sure "top" on the bushing retainer is up so the mixing arm runs straight between the round bushing and the square drive in. Remove the mixing arm after disassembly of the grinder cylinder and worm. Re-assemble the mixing arm before assembly of the cylinder and worm. The MG1532 has a hopper capacity of up to 150 pounds of fresh meat, depending on the type of product. The MG2032 has a hopper capacity of up to 200 pounds of fresh meat, depending on the type of product. Second cut meat may be mixed in the hopper for any desired length of time. During the mix operation, the mixing arm rotates and the grinding worm does not. Continuous self-feeding occurs along with grinding in the mix/grind operation. Mixing of uncut or unground meat is not recommended. Grinding procedures are as follows: for the first grind fill the hopper and close and latch the hopper lid. Overfilling will bend the hopper lid and may cause the interlock to open the circuit. Push the mix/grind button to start grinding. Press the stop button to stop grinding. Second grind, fill the hopper and close and latch the hopper lid. Press the mix button. After desired mixing, press the stop button. Then press the mix/grind button to start grinding. Press the stop button to stop grinding or activate and use the optional foot switch. Warning: disconnect the electrical power supply before cleaning or servicing this machine. In any cleaning operation, after disconnecting the electrical supply, seal the receptacle to prevent the entrance of moisture. To make this seal on Hobart supplied receptacles and pendent connectors, place the cover cap into position and turn the screw tight sealing ring clockwise. Remove the following components when cleaning: the mixing arm, grinder adjusting ring, knife, plate, cylinder, worm, and the side feed hopper plug if used. Refer to your instruction manual which came with your Hobart mixer/grinder for the correct method of removal. The mixing arm seal and the worm seal should be removed by hand for cleaning. Grasp the outer flange or use a dull screwdriver to pry the seal loose. The machine can be washed down with hot water or steam as is customary in meat processing operations. When using detergents and sanitizers, follow the manufacturer's instructions. Rinse with clear water and allow to air dry. After cleaning the machine, apply food grade mineral oil to lubricate the inside rim of the mixing arm seals and the worm seal where the mixing arm and worm will touch the seals. Reassemble the mixing arm seal, worm seal, mixing arm, and the bushing retainer. To reassemble the mix arm and worm seals, align the tab at the bottom of each seal with the notch at the bottom of the applicable seal hole in the end wall of the hopper. The arrow at the top of the seal points up. Squeeze the sides of the seal and push in. Push in the top of the seal. Make sure the seals are properly sealed. After cleaning, a light coat of food grade mineral oil is recommended for the cylinder, adjusting ring, knife, plate, and worm before reassembly. This concludes Operator Training for the Hobart 1532 and 2032 mixer/grinders. To obtain service parts information concerning this mixer, contact your local Hobart service office.

Copy and paste the embed code above.

Watch this video to learn how to properly operate and care for your Hobart MG1532 and MG2032 mixer/grinders.

Hobart MG1532-1 208/3 Specs
Width 26 7/8 Inches
Depth 50 3/4 Inches
Height 84 1/8 Inches
Hertz 60 Hertz
Phase 3
Voltage 208 Volts
Capacity 55 - 65 lb. per minute
Horsepower 7 1/2 HP
Hub Size #32
Made in America Yes
Power Type Electric
Type Meat Choppers / Grinders
Usage Heavy Duty

Customer questions about this product

Can this item fit through a standard height 80" doorway?
Due to the height of this item, it may not be able to fit through a standard 80" tall doorway when standing upright. Please consider the best means of entry before purchasing, or measure your entryway to ensure that you will be able to bring your order inside if the item cannot be carried on its side.
Ask your own question!

Hobart MG1532-1 208/3 Details

Boasting a 150 lb. meat capacity, the Hobart MG1532-1 # 32 meat mixer / grinder is perfect for heavy duty meat prep! Plus, its foot control option allows for precise, hands free operation! This compact-design grinder / mixer can grind 55 to 60 lb. of fresh boneless beef per minute through a 1/8" plate, and 60 to 65 lb. of pork per minute through a 3/16" plate (plates sold separately).

- Pneumatic (air drive) foot control for hands-free operation

- Counterbalanced lid and double wall construction

- Easy access hopper and exterior surfaces

- Grinds fresh or frozen meat tempered to 26 degrees Fahrenheit or higher in both flake or stick form

- Wedge cylinder grinding end designed for use with standard # 32 knives and plates (sold separately)

- Powered by 7.5 H.P. grind motor and a 1 H.P. mix motor with guard and electrical interlock system for safety

- All food contact surfaces are easily cleanable

- Glass bead finished stainless steel hopper, stainless steel panels, stainless steel ring and cylinder, tinned mixing arm and conveyor screw

- Also includes drain pan, meat deflector, and (2) fixed adjustable casters

Overall Dimensions:
Width: 26 7/8"
Depth: 50 3/4"
Height (including hopper): 84 1/8"

This Item Ships via Common Carrier. For more information and tips to help your delivery go smoothly, click here.

Because this item is not stocked in our warehouse, processing, transit times and stock availability will vary. If you need your items by a certain date, please contact us prior to placing your order. Expedited shipping availability may vary. We cannot guarantee that this item can be cancelled off of the order or returned once it is placed.

Resources and Downloads for
Hobart MG1532-1 208/3

Specsheet Specsheet Manual Manual Hobart's Warranty Information Warranty Parts Diagram Diagram

A PDF viewer is required to view this product's information. Download Adobe Acrobat software

Warranty Info

RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure or other damages resulting from installation in non-commercial or residential applications. The right is reserved to deny shipment for residential usage; if this occurs, you will be notified as soon as possible.

Get paid to review this product!

If you've used this product, simply log in and share your text, video, and photo reviews of it. The customers on the left did it, and you can too! Earn up to $16.00 per product.

Login or Register